What surfaces is this foam spray suitable for?

Use it to remove mould and black stains from tile joints, silicone seals, and plaster in damp areas.

What is the benefit of the foam formula?

The foam adheres longer to vertical surfaces, targets spots accurately, splashes less, and has a less pungent odour.

What is the recommended working time?

Spray the surface from a distance of 3 to 5 cm, leave it to work for 30 minutes, then clean with water and a sponge.

Should you scrape away the mould before applying?

No, do not remove mould beforehand. Spray directly onto the affected area to prevent spreading mould spores.

What is the net volume of this bottle?

The spray bottle contains 500 ml of ready-to-use cleaner.

HG 632050103 mould cleaner foam spray 500 ml

Supplier number: HG 632050103 | EAN 8711577207830

10.62 tax incl.

€8.78 excl. VAT (incl. all environmental contributions)

On stock - immediately available | we have 5 products in stock.

Delivery by DHL

✆ Talk to a specialist

Targeted cleaning with Hg foam

Practical benefits

Clings to vertical surfaces: The targeted foam formula adheres directly to tile joints and silicone seals, ensuring extended contact time without running down.
Reduced splashing during application: You can direct the spray precisely where needed, which minimises splashing and reduces strong odours during application.
Fast acting mould removal: Within 30 minutes, the self-acting formula breaks down stubborn black spots so you can easily wipe the surface clean.

In a nutshell

The right choise for

With the Hg mould remover foam spray 500 ml, you can easily eliminate stubborn black mould and stains in damp environments. The targeted foam formula clings directly to vertical walls, tile grout, and silicone seals in bathrooms, showers, and basements without immediately running down. This extended contact time ensures a deep, self-acting clean while reducing splashing and strong odours during application. Simply spray the ready-to-use cleaner onto the affected surface, leave it to work for 30 minutes, and wipe it away with a sponge and water for a fresh, clean finish.

Product information FAQ

€10.62

In stock - tax incl.

Key features according to our expert

Cleaner type: Mould stain remover
P-statements: P101; P102; P264; P280; P301 + P330 + P331; P303 + P361 + P353; P305 + P351 + P338; P310; P405; P501
ADR packing group: II
ADR class: 8
UN number: UN3267
Net volume: 500 ml
EUH-statements: EUH206
Principal hazard property: GHS05 Corrosive
H-statements: H290; H314; H318; H400; H410; H411
Hazard class: GHS05 Corrosive; GHS09 Environmental hazard
Physical state: Liquid
Packaging: Spray can

Product description

Less pungent odour
Better to target

HG mould stain cleaners instantly destroy all mould, making the dirty black spots disappear. These unsightly black mould, moisture or weather spots are common in silicone joints between bathtub and tile wall, in the shower cubicle and in plasterwork. A regular spray variant is available: the HG mould stain cleaner, as well as a foam spray: the HG mould stain cleaner foam spray. Both extremely effective, but the unique foam formula has a less pungent smell, is even better at targeting the mould and, of course, gives less chance of splashing. In addition, the foam has the property of staying on longer and therefore provides better and longer penetration.

Instructions for use

Remove the lock before use
If you have used the bottle before, there may be residue of the liquid left in the nozzle which could impair its performance when reused. We therefore advise you to always rinse the nozzle thoroughly with hot water from the tap, e.g. via the vent holes on the side of the foam nozzle, in case of reuse.
The product has a bleaching effect; in case of doubt, first test on an inconspicuous place
Do not remove mould in advance
Press the nipple on the front side and turn a quarter turn
Spray the surface from a distance of 3-5 cm
In case of stubborn contamination, spray again after 30 minutes and allow to take effect for 30 minutes
Clean the sprayed surface with water and a sponge
Wash off elastic joints (e.g. silicone sealant) after approx. 30 minutes and spray again
After use, turn back the nipple a quarter turn (lock position)
Consumption: 2-3 m2 wall surface, 6-8 m2 tile joints

Precautionary statements

P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
P264: Wash ... (see safety data sheet) thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P301 + P330 + P331: IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water (or shower).
P305 + P351 + P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P310: Immediately call a POISON CENTER/doctor/…
P405: Store locked up.
P501: Dispose of contents/container to ... (see safety data sheet).

Hazard statements

H290: May be corrosive to metals.
H314: Causes severe skin burns and eye damage.
H318: Causes serious eye damage.
H400: Very toxic to aquatic life.
H410: Very toxic to aquatic life with long lasting effects.
H411: Toxic to aquatic life with long lasting effects.

Supplemental hazard information

EUH206: Warning! Do not use together with other products. May release dangerous gases (chlorine).

All Features

Cleaner type: Mould stain remover
P-statements: P101; P102; P264; P280; P301 + P330 + P331; P303 + P361 + P353; P305 + P351 + P338; P310; P405; P501
Adr packing group: II
Adr class: 8
Un number: UN3267
Net volume: 500 ml
Euh-statements: EUH206
Principal hazard property: GHS05 Corrosive
H-statements: H290; H314; H318; H400; H410; H411
Hazard class: GHS05 Corrosive; GHS09 Environmental hazard
Physical state: Liquid
Packaging: Spray can

Brand HG
08123614
EAN 8711577207830
Supplier number HG 632050103

Frequently asked questions about this product

Answered by specialists

What surfaces is this foam spray suitable for?: Use it to remove mould and black stains from tile joints, silicone seals, and plaster in damp areas.
What is the benefit of the foam formula?: The foam adheres longer to vertical surfaces, targets spots accurately, splashes less, and has a less pungent odour.
What is the recommended working time?: Spray the surface from a distance of 3 to 5 cm, leave it to work for 30 minutes, then clean with water and a sponge.
Should you scrape away the mould before applying?: No, do not remove mould beforehand. Spray directly onto the affected area to prevent spreading mould spores.
What is the net volume of this bottle?: The spray bottle contains 500 ml of ready-to-use cleaner.