r: 02020200 p: 19.669 pid: 96813 b: FISCHER q: 0 st: lt: 8 ean: 4006209972977 sr: FISCHER 97297 sr_no_br: 97297 sr_no_br_cl: 97297 sr_cl: FISCHER97297 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 24 mm Length 170 mm Anchoring depth 170 mm Width across flats 36 mm Effective length 50 mm Drill hole depth 190 mm Drilling diameter 25 mm n: FISCHER 97297 highbond anchor FHB II-A S M24 x 170/50 ev cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete with the least installation effort. The fischer Highbond rod anchor FHB II-A S is produced from zinc-plated steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that railings, machines and heavy steel constructions are securely installed within internal areas. Reduces anchorage depth, lowers expense when drilling and installing. This saves costs Through-type installations without additional aids. This saves time Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The reduced anchorage depth of the FHB II-A S minimises the drilling and installation effort. In addition using the combination with FHB II-P/-PF capsule no drill hole cleaning is required. Thus allowing for an especially economical and time-saving fixing With the anchor rod FHB II-A S, the drill bit diameter is the same as the thread diameter. This allows for push-through installation without any tools and reduces the amount of mortar required The cone shape of the anchor rod FHB II-A S is optimised for small axial and edge distances in cracked concrete, as well as thin concrete members. As a result, it is suitable for a wide range of applications The anchor rod FHB II-A S is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application Suitable for The FHB II-A S is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation With the FHB II-A S, the drill bit diameter is the same as the thread diameter, similar to with an anchor bolt The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Suitable for: Guard rails Façades Staircases Steel brackets Masts Rash protection Steelwork constructions Timber constructions Ideal for: Push-through installation ds: dsc: kts: highbond anchor FHB II-A S M24 x 170/50 ev kpn: 97297 kpn_dash: kpn_clear: 97297 bkpn: FISCHER 97297 bkpn_clear: FISCHER 97297 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97297 sr_ns: FISCHER97297
r: 02020596 p: 19.173 pid: 16005 b: FISCHER q: 0 st: lt: 8 ean: 4006209976210 sr: FISCHER 97621 sr_no_br: 97621 sr_no_br_cl: 97621 sr_cl: FISCHER97621 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm Anchoring depth 120 mm Width across flats 19 mm Effective length 10 mm Drill hole depth 135 mm Drilling diameter 14 mm n: FISCHER 97621 highbond anchor FHB II-A L M12 x 120/10 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete for maximum tension loads - even outdoors. The fischer Highbond rod anchor FHB II-A L is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, silos, and heavy steel constructions are securely installed within external areas. Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required Optimised anchor rod for the highest tensile loads Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools Suitable for The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall The styrene-free vinyl ester mortar fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Guard rails Façades Staircases Steel brackets Machines Silo installations Masts Rash protection Steelwork constructions Timber constructions ds: dsc: kts: highbond anchor FHB II-A L M12 x 120/10 stainless steel A4 kpn: 97621 kpn_dash: kpn_clear: 97621 bkpn: FISCHER 97621 bkpn_clear: FISCHER 97621 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97621 sr_ns: FISCHER97621
r: 08096871 p: 18.966 pid: 176272 b: FISCHER q: 0 st: lt: 8 ean: 4048962462319 sr: FISCHER 564606 sr_no_br: 564606 sr_no_br_cl: 564606 sr_cl: FISCHER564606 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 24 mm Effective length 60 mm Overall length 235 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M24 n: FISCHER 564606 Piercing anchor FAZ II Plus 24/60 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 24/60 EV electrolytically galvanised steel kpn: 564606 kpn_dash: kpn_clear: 564606 bkpn: FISCHER 564606 bkpn_clear: FISCHER 564606 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564606 sr_ns: FISCHER564606
r: 02020559 p: 18.016 pid: 96446 b: FISCHER q: 0 st: lt: 8 ean: 4006209976418 sr: FISCHER 97641 sr_no_br: 97641 sr_no_br_cl: 97641 sr_cl: FISCHER97641 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Anchoring depth 95 mm Width across flats 24 mm Effective length 30 mm Drill hole depth 110 mm Drilling diameter 16 mm n: FISCHER 97641 highbond anchor FHB II-A S M16 x 95/30 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete with the least installation effort - even outdoors. The fischer Highbond rod anchor FHB II-A S A4 is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, railings, and steel constructions are securely installed within external areas. Reduces anchorage depth, lowers expense when drilling and installing. This saves costs Through-type installations without additional aids. This saves time Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The reduced anchorage depth of the FHB II-A S minimises the drilling and installation effort. In addition using the combination with FHB II-P/-PF capsule no drill hole cleaning is required. Thus allowing for an especially economical and time-saving fixing With the anchor rod FHB II-A S, the drill bit diameter is the same as the thread diameter. This allows for push-through installation without any tools and reduces the amount of mortar required The cone shape of the anchor rod FHB II-A S is optimised for small axial and edge distances in cracked concrete, as well as thin concrete members. As a result, it is suitable for a wide range of applications The anchor rod FHB II-A S is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application Suitable for The FHB II-A S is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation With the FHB II-A S, the drill bit diameter is the same as the thread diameter, similar to with an anchor bolt The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Suitable for: Guard rails Façades Staircases Steel brackets Masts Rash protection Steelwork constructions Timber constructions Ideal for: Push-through installation ds: dsc: kts: highbond anchor FHB II-A S M16 x 95/30 stainless steel A4 kpn: 97641 kpn_dash: kpn_clear: 97641 bkpn: FISCHER 97641 bkpn_clear: FISCHER 97641 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97641 sr_ns: FISCHER97641
r: 02019477 p: 17.685 pid: 10865 b: FISCHER q: 0 st: lt: 4 ean: 4006209484166 sr: FISCHER 48416 sr_no_br: 48416 sr_no_br_cl: 48416 sr_cl: FISCHER48416 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Drilling diameter 20 mm n: FISCHER EA II M16x65 A4 weft anchor stainless steel - 48416 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The internally threaded anchor made of stainless steel with a rim for simple Hammerset installation. The fischer Hammerset anchor EA II R is an internal threaded anchor made of stainless steel. The Hammerset anchor is set flush to the surface of the anchoring base using the hammer. With the setting tool EHS Plus or the machine setting tool EMS the sleeve is expanded by driving in the internal rod and expands against the drill hole wall. For correct expansion to take place, no torque must be applied to the screw or the threaded rod. The fischer Hammerset anchor EA II R is ideal for fixing steel constructions and formwork props in external areas with approval. Simple Hammerset installation: no slippage during assembly due to the pronounced edge on the anchor sleeve Use of standard metric screws and threaded rods lowers complexity Power-saving series installation with machine setting tool EA II S-SDS ETA approval for non-cracked concrete Made of stainless steel for fixings used outside The embossed rim prevents the anchor sleeve from slipping, thus ensuring a trouble-free hammerset installation The metric internal thread means that it is possible to use standard screws or threaded rods for the ideal adaptation to suit the intended use The EMS machine setting tool allows for effortless installation, particularly in the case of series installations The embossing that is applied when expanding with the EHS Plus setting tool offers a simple control of the anchoring and provides increased safety Fixing point at hef 25 mm prevents anchor of falling out of the drill hole before being expanded The black fixing point prevents the anchor from falling out of the drill hole during overhead installation Suitable for The EA II is suitable for pre-positioned installation Position the hammerset anchor in the drill hole and drive in flush to the surface of the anchor base using the hammer The sleeve is then expanded by driving in the internal bolt with the EHS Plus setting tool (alternative: EMS machine setting tool), and expanded against the drill hole wall The setting tools must sit on the rim of the anchor to ensure correct expansion Building materials Approved for: Concrete C20/25 to C50/60, cracked, for the multiple fixings of non-load-bearing systems Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Pipelines and ventilation ducts Sprinkler systems Cable conduits and wires Gratings Steel constructions Machines Consoles Shuttering props ds: dsc: kts: weft anchor stainless steel kpn: EA II M16x65 A4 kpn_dash: kpn_clear: EAIIM16x65A4 bkpn: FISCHER EA II M16x65 A4 bkpn_clear: FISCHER EAIIM16x65A4 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 48416 sr_ns: FISCHER48416
r: 02137076 p: 17.314 pid: 21597 b: FISCHER q: 0 st: lt: 8 ean: 4006209502679 sr: FISCHER 50267 sr_no_br: 50267 sr_no_br_cl: 50267 sr_cl: FISCHER50267 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 20 mm Length 260 mm Material Stainless steel A4 Drilling diameter 25 mm n: FISCHER 50267 anchor rod RG M20 x 260 R stainless steel cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The proven rod anchor for external use with a mortar cartridge or injection mortar. The fischer rod anchor RG M is produced from stainless steel. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in external areas. Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge Stainless steel for outdoor use The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety Please refer to the approvals for the resin capsules and mortar used Suitable for Due to its oblique edge, the anchor rod RG M is particularly suitable for use in conjunction with resin capsules The anchor rod RG M is set using a hammer drill and the accompanying setting tool in rotating and hitting motions During setting, the oblique edge of the RG M destroys the capsule, and mixes and activates the mortar Use with injection mortar is also possible. Here, the anchor rod is manually inserted into the drill hole with a light rotating movement until it reaches the base of the hole Building materials In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete In connection with several fischer injection mortars approved or suitable for different building materials Application Anchorings with resin capsule RSB and RSB mini Anchorings with resin capsule RM II Anchorings with each of the fischer injection mortars FIS SB, FIS EM, FIS EB II, FIS V, FIS VL, FIS V Zero, FIS P Plus, FIS P, FIS EP and FIS Green ds: dsc: kts: anchor rod RG M20 x 260 R stainless steel kpn: 50267 kpn_dash: kpn_clear: 50267 bkpn: FISCHER 50267 bkpn_clear: FISCHER 50267 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 50267 sr_ns: FISCHER50267
r: 87051311 p: 17.19 pid: 17220 b: FISCHER q: 0 st: lt: 8 ean: 4006209607848 sr: FISCHER 60784 sr_no_br: 60784 sr_no_br_cl: 60784 sr_cl: FISCHER60784 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm n: FISCHER FZA 12x50 M6 R Zykon female threaded anchor stainless steel - 60784 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The internally threaded anchor consists of stainless steel for optimum safety in cracked concrete. The fischer ZYKON internal threaded anchor FZA-I is an anchor made of stainless steel. The special drill bit FZUB is used to create the undercut drill hole in a single work step. The undercut anchor is set in the pre-positioned installation. The expansion sleeve is driven above the cone with the setting tool FZE Plus and fills the undercut drill hole with a positive fit. The fischer ZYKON internal threaded anchor FZA-I is ideal for fixing steel constructions, staircases, and temporary fixings within external areas in cracked concrete. Maximum safety due to a positive fit connection High flexibility due to using conventional metric screws and threaded rods Fast installation, no exchanging tools. This saves time and costs ETA approval for cracked concrete and fire resistance class R 120 Made of stainless steel for fixings used outside The special ZYKON undercut technology allows for a positive fit connection and ensures maximum safety, even in large cracks The metric internal thread means that it is possible to use standard screws or threaded rods for the ideal adaptation to suit the intended use The FZA-I allows for surface flush removal and reuse of the fixing point, and therefore offers the best possible flexibility Furthermore, the ZYKON undercut anchor FZA-I offers all the benefits of the FZA Suitable for FZA-I with internal thread is suitable for pre-positioned installation The undercut drill hole is created using the special FZUB drill Once the anchor has been placed in the drill hole, the expansion sleeve is driven over the cone using the FZE Plus setting tool, and the undercut drill hole is filled with a positive fit Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates ds: dsc: kts: Zykon female threaded anchor stainless steel kpn: FZA 12x50 M6 R kpn_dash: kpn_clear: FZA12x50M6R bkpn: FISCHER FZA 12x50 M6 R bkpn_clear: FISCHER FZA12x50M6R c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 60784 sr_ns: FISCHER60784
r: 03374663 p: 16.694 pid: 176217 b: FISCHER q: 0 st: lt: 1 ean: 4048962540628 sr: FISCHER 574698 sr_no_br: 574698 sr_no_br_cl: 574698 sr_cl: FISCHER574698 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Net volume 150 ml Principal hazard property GHS07 Harmful or irritant Relative density 1 ADR packing group III ADR class 9 Packaging Can UN number UN3077 Conseils de prudence (P) P101; P102; P280; P501; P273; P391 H-statements H315; H317; H319; H400; H410 Hazard class GHS07 Harmful or irritant; GHS09 Environmental hazard Physical state Solid Flash point > 100 °C n: FISCHER 574698 injection mortar FIS VS Plus 150 C cn: INJECTION MORTAR cn2: INJECTION MORTAR cn_clear: INJECTIONMORTAR d: Product description The versatile injection mortar for installation in cracked concrete and masonry. The injection mortar FIS V Plus has numerous certifications, such as for cracked and uncracked concrete, solid and perforated masonry, aerated concrete as well as for special system applications. ETA certification for a service life of 100 years provides permanent safety for all applications. The certified use in water-filled boreholes allows an even wider range of applications, even under the harshest environmental conditions. The extensive range of accessories in the FIS V Plus range increases the flexibility of the system, enabling a wide range of applications. The fischer high-performance Injection Mortar FIS V Plus is the universal chemical anchor for the highest demands. The styrene-free vinylester hybrid mortar with its numerous anchors is certified for anchoring in cracked and uncracked concrete, solid and perforated masonry as well as aerated concrete. The FIS V Plus is used for bonding Anchor rods FIS A / RG M and internal threaded anchor RG M I. However, the injection mortar is also used in combination with reinforcement rods, the fischer renovation anchor VBS 8 and the spacer system TherMax. The shorter curing time of the variant FIS VW Plus allows a quick turnaround time even at low temperatures. Applications Steel structures Timber structures Handrails Façade systems Stairs Anchorage Machinery Awnings Awnings Fencing Brackets Building materials Certified for anchorages in: Concrete C20/25 to C50/60, cracked and uncracked Lightweight concrete hollow brick Concrete hollow brick Perforated clay brick Perforated sand-lime brick Solid sand-lime brick Aerated concrete Solid brick Certified as a system for: Bonding of reinforcement Renovation anchor VBS 8 Distance mounting system TherMax ds: dsc: kts: injection mortar FIS VS Plus 150 C kpn: 574698 kpn_dash: kpn_clear: 574698 bkpn: FISCHER 574698 bkpn_clear: FISCHER 574698 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Injection mortar | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer injection mortar sr_no_br_cl_ns: 574698 sr_ns: FISCHER574698
r: 02020557 p: 16.363 pid: 17482 b: FISCHER q: 0 st: lt: 8 ean: 4006209976395 sr: FISCHER 97639 sr_no_br: 97639 sr_no_br_cl: 97639 sr_cl: FISCHER97639 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm Anchoring depth 75 mm Width across flats 19 mm Effective length 100 mm Drill hole depth 90 mm Drilling diameter 12 mm n: FISCHER 97639 highbond anchor FHB II-A S M12 x 75/100 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete with the least installation effort - even outdoors. The fischer Highbond rod anchor FHB II-A S A4 is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, railings, and steel constructions are securely installed within external areas. Reduces anchorage depth, lowers expense when drilling and installing. This saves costs Through-type installations without additional aids. This saves time Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The reduced anchorage depth of the FHB II-A S minimises the drilling and installation effort. In addition using the combination with FHB II-P/-PF capsule no drill hole cleaning is required. Thus allowing for an especially economical and time-saving fixing With the anchor rod FHB II-A S, the drill bit diameter is the same as the thread diameter. This allows for push-through installation without any tools and reduces the amount of mortar required The cone shape of the anchor rod FHB II-A S is optimised for small axial and edge distances in cracked concrete, as well as thin concrete members. As a result, it is suitable for a wide range of applications The anchor rod FHB II-A S is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application Suitable for The FHB II-A S is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation With the FHB II-A S, the drill bit diameter is the same as the thread diameter, similar to with an anchor bolt The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Suitable for: Guard rails Façades Staircases Steel brackets Masts Rash protection Steelwork constructions Timber constructions Ideal for: Push-through installation ds: dsc: kts: highbond anchor FHB II-A S M12 x 75/100 stainless steel A4 kpn: 97639 kpn_dash: kpn_clear: 97639 bkpn: FISCHER 97639 bkpn_clear: FISCHER 97639 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97639 sr_ns: FISCHER97639
r: 08096873 p: 16.198 pid: 176285 b: FISCHER q: 0 st: lt: 8 ean: 4048962462302 sr: FISCHER 564605 sr_no_br: 564605 sr_no_br_cl: 564605 sr_cl: FISCHER564605 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 24 mm Effective length 30 mm Overall length 205 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M24 n: FISCHER 564605 Piercing anchor FAZ II Plus 24/30 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 24/30 EV electrolytically galvanised steel kpn: 564605 kpn_dash: kpn_clear: 564605 bkpn: FISCHER 564605 bkpn_clear: FISCHER 564605 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564605 sr_ns: FISCHER564605
r: 08096852 p: 16.198 pid: 176235 b: FISCHER q: 0 st: lt: 8 ean: 4048962462623 sr: FISCHER 564637 sr_no_br: 564637 sr_no_br_cl: 564637 sr_cl: FISCHER564637 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 8 mm Effective length 50 mm Overall length 115 mm Material (bolt) Steel Surface treatment (bolt) None Thread designation M8 n: FISCHER 564637 Piercing anchor FAZ II Plus 8/50 HCR high-corrosion steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 8/50 HCR high-corrosion steel kpn: 564637 kpn_dash: kpn_clear: 564637 bkpn: FISCHER 564637 bkpn_clear: FISCHER 564637 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564637 sr_ns: FISCHER564637
r: 08096964 p: 14.71 pid: 176363 b: FISCHER q: 0 st: lt: 8 ean: 4048962462630 sr: FISCHER 564638 sr_no_br: 564638 sr_no_br_cl: 564638 sr_cl: FISCHER564638 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 10 mm Overall length 95 mm Material (bolt) Steel Surface treatment (bolt) None Thread designation M10 n: FISCHER 564638 Piercing anchor FAZ II Plus 10/10 HCR high-corrosion steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 10/10 HCR high-corrosion steel kpn: 564638 kpn_dash: kpn_clear: 564638 bkpn: FISCHER 564638 bkpn_clear: FISCHER 564638 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564638 sr_ns: FISCHER564638
r: 02020737 p: 14.71 pid: 12898 b: FISCHER q: 0 st: lt: 8 ean: 4006209920190 sr: FISCHER 92019 sr_no_br: 92019 sr_no_br_cl: 92019 sr_cl: FISCHER92019 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 12 mm Anchoring depth 100 mm Width across flats 19 mm Effective length 8 - 50 mm Drill hole depth 155 mm Drilling diameter 14 mm n: FISCHER 92019 highbond anchor FHB-A dynamic 12 x 100/50 ev cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The highest performance in class amongst dynamic anchors The fischer Highbond anchor dynamic FHB-A dyn is made of zinc-plated steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. During the setting process, the injection mortar FIS HB fills the annular gap in the fixture, and guarantees optimum load distribution. This allows for the absorption of dynamic alternating loads. The fischer Highbond anchor dynamic FHB-A dyn is ideally suited for fixing guide rails for elevators, industrial robots, or mobile portal and ceiling cranes in internal areas. Controlled expansion under dynamic stress due to cone shape Absorption of dynamic alternating loads via optimum load distribution Approved for cracked concrete The Highbond-anchor dynamic FHB-A dyn must be applied in combination with the Highbond-mortar FIS HB During the setting process, the injection mortar FIS HB fills the annular gap in the fixture, and ensures optimum load distribution. This allows for the absorption of dynamic alternating loads The cone shape of the FHB-A dyn anchor rod ensures a controlled expansion under dynamic stress, thus allowing for use in cracked concrete The anchor rod FHB-A dyn is also available made from high corrosion-resistant steel. This makes it suitable for use in aggressive atmospheres, for example in tunnels The Highbond anchor dynamic system can achieve even greater shear loads thanks to the additional sleeve of the anchor rod FHB-A dyn V, and therefore provides an increased level of safety The ETA for static and quasi-static loads allows the use of sizes M12 and M16 also for the anchoring base steel fiber concrete Suitable for The injection system suitable for tensile zones consists of the Highbond dynamic anchor rod FHB-A dyn and the injection mortar FIS HB FHB dyn is approved for pre-positioned and push-through installation Extruding the mortar causes the two components to be mixed and activated in the static mixer The mortar bonds the entire surface of the anchor rod with the drill hole wall and seals the drill hole The centring sleeve centres the anchor in the fixture, thus ensuring a safe load application The lock nut prevents the nut from becoming loose Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Steel fiber reinforced concrete (M12 / M16) Application Jib cranes Gantry and overhead cranes Guide rails for elevators Tunnel ventilators (jet fans) Gantries in road construction Antennas and transmitter masts Industrial robots ds: dsc: kts: highbond anchor FHB-A dynamic 12 x 100/50 ev kpn: 92019 kpn_dash: kpn_clear: 92019 bkpn: FISCHER 92019 bkpn_clear: FISCHER 92019 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 92019 sr_ns: FISCHER92019
r: 02020154 p: 14.545 pid: 10584 b: FISCHER q: 0 st: lt: 13 ean: 4006209505564 sr: FISCHER 50556 sr_no_br: 50556 sr_no_br_cl: 50556 sr_cl: FISCHER50556 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Drilling diameter 24 mm Overall length 90 mm n: FISCHER SL M16 sleeve anchor electrolytically galvanised steel - 50556 cn: ANCHOR SLEEVE cn2: ANCHOR SLEEVE cn_clear: ANCHORSLEEVE d: Product description The classical steel anchor for all metrical screws. The fischer heavy-duty anchor SL M is a sleeve anchor with internal thread made of zinc-plated steel. When tightening the screw, the cone is pulled into the expansion sleeve and expands it against the hole wall. The SL M is suitable for stand-off installation and for pre-positioned installation. The fischer heavy-duty anchor SL M is ideal for cost-effective fixing of machines or consoles in internal areas. High flexibility: Internal thread is suitable for screws and threaded bolts with metric thread Repeated loosening and installing of the component for adjustment is possible Surface flush removal possible Plastic cap on cone protects internal thread from drilling dust. This ensures that the thread remains functional The optimised geometry minimises setting energy and allows for use in extremely narrow spaces. This allows for user-friendly installation The three-part expansion sleeve creates even load distribution, thus allowing small edge and axial spacing. Thus the TA M is extremely flexible The metric internal thread allows to use standard screws or threaded rods for the ideal adaptation to suit the intended use The red plastic cap protects against soiling and thus ensures free-running of the thread Suitable for The SL M is suitable for pre-positioned installation When applying the torque, the cone is pulled into the expansion sleeve and expands it against the drill hole wall For correct installation, it must be ensured that the pre-positioned anchor SL M can be supported on the attachment, or that the threaded rod is countered Building materials Concrete C20/25 to C50/60, non-cracked Concrete C12/15 Natural stone with dense structure Application Steel constructions Handrails Consoles Ladders Cable trays Machines Staircases Gates Façades Stand-off installations ds: dsc: kts: sleeve anchor electrolytically galvanised steel kpn: SL M16 kpn_dash: kpn_clear: SLM16 bkpn: FISCHER SL M16 bkpn_clear: FISCHER SLM16 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor sleeve | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor sleeve sr_no_br_cl_ns: 50556 sr_ns: FISCHER50556
r: 08096878 p: 14.38 pid: 176233 b: FISCHER q: 0 st: lt: 8 ean: 4048962462296 sr: FISCHER 564604 sr_no_br: 564604 sr_no_br_cl: 564604 sr_cl: FISCHER564604 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 20 mm Effective length 160 mm Overall length 302 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread designation M20 n: FISCHER 564604 Piercing anchor FAZ II Plus 20/160 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 20/160 EV electrolytically galvanised steel kpn: 564604 kpn_dash: kpn_clear: 564604 bkpn: FISCHER 564604 bkpn_clear: FISCHER 564604 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564604 sr_ns: FISCHER564604
r: 02020219 p: 14.008 pid: 17467 b: FISCHER q: 0 st: lt: 8 ean: 4006209970355 sr: FISCHER 97035 sr_no_br: 97035 sr_no_br_cl: 97035 sr_cl: FISCHER97035 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 16 mm Length 160 mm Anchoring depth 160 mm Width across flats 24 mm Effective length 30 mm Drill hole depth 175 mm Drilling diameter 18 mm n: FISCHER 97035 highbond anchor FHB II-A L M16 x 160/30 ev cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete for maximum tensile loads. The fischer Highbond rod anchor FHB II-A L is produced from zinc-plated steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that large machines and heavy steel constructions are securely installed within internal areas. Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required Optimised anchor rod for the highest tensile loads Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools Suitable for The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall The styrene-free vinyl ester mortar fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Guard rails Façades Staircases Steel brackets Machines Silo installations Masts Rash protection Steelwork constructions Timber constructions ds: dsc: kts: highbond anchor FHB II-A L M16 x 160/30 ev kpn: 97035 kpn_dash: kpn_clear: 97035 bkpn: FISCHER 97035 bkpn_clear: FISCHER 97035 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97035 sr_ns: FISCHER97035
r: 08096879 p: 13.884 pid: 176239 b: FISCHER q: 0 st: lt: 10 ean: 4048962462548 sr: FISCHER 564629 sr_no_br: 564629 sr_no_br_cl: 564629 sr_cl: FISCHER564629 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 60 mm Overall length 183 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread designation M16 n: FISCHER 564629 piercing anchor FAZ II Plus 16/60 R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Stainless steel: maximum safety for outdoor use Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: piercing anchor FAZ II Plus 16/60 R stainless steel kpn: 564629 kpn_dash: kpn_clear: 564629 bkpn: FISCHER 564629 bkpn_clear: FISCHER 564629 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564629 sr_ns: FISCHER564629
r: 02020576 p: 13.719 pid: 16003 b: FISCHER q: 0 st: lt: 8 ean: 4006209976197 sr: FISCHER 97619 sr_no_br: 97619 sr_no_br_cl: 97619 sr_cl: FISCHER97619 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 10 mm Anchoring depth 95 mm Width across flats 17 mm Effective length 60 mm Drill hole depth 110 mm Drilling diameter 12 mm n: FISCHER 97619 highbond anchor FHB II-A L M10 x 95/60 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete for maximum tension loads - even outdoors. The fischer Highbond rod anchor FHB II-A L is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, silos, and heavy steel constructions are securely installed within external areas. Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required Optimised anchor rod for the highest tensile loads Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools Suitable for The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall The styrene-free vinyl ester mortar fully seals the drill hole When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Guard rails Façades Staircases Steel brackets Machines Silo installations Masts Rash protection Steelwork constructions Timber constructions ds: dsc: kts: highbond anchor FHB II-A L M10 x 95/60 stainless steel A4 kpn: 97619 kpn_dash: kpn_clear: 97619 bkpn: FISCHER 97619 bkpn_clear: FISCHER 97619 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97619 sr_ns: FISCHER97619
r: 02020545 p: 13.553 pid: 17078 b: FISCHER q: 0 st: lt: 8 ean: 4006209976340 sr: FISCHER 97634 sr_no_br: 97634 sr_no_br_cl: 97634 sr_cl: FISCHER97634 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Wire dimension 10 mm Anchoring depth 60 mm Width across flats 17 mm Effective length 100 mm Drill hole depth 75 mm Drilling diameter 10 mm n: FISCHER 97634 highbond anchor FHB II-A S M10 x 60/100 stainless steel A4 cn: ANCHOR ROD cn2: ANCHOR ROD cn_clear: ANCHORROD d: Product description The best performance in cracked concrete with the least installation effort - even outdoors. The fischer Highbond rod anchor FHB II-A S A4 is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, railings, and steel constructions are securely installed within external areas. Reduces anchorage depth, lowers expense when drilling and installing. This saves costs Through-type installations without additional aids. This saves time Optimised for low axial and edge distances in cracked concrete No drill hole cleaning is required when using a resin capsule. This saves time ETA approval for cracked concrete The reduced anchorage depth of the FHB II-A S minimises the drilling and installation effort. In addition using the combination with FHB II-P/-PF capsule no drill hole cleaning is required. Thus allowing for an especially economical and time-saving fixing With the anchor rod FHB II-A S, the drill bit diameter is the same as the thread diameter. This allows for push-through installation without any tools and reduces the amount of mortar required The cone shape of the anchor rod FHB II-A S is optimised for small axial and edge distances in cracked concrete, as well as thin concrete members. As a result, it is suitable for a wide range of applications The anchor rod FHB II-A S is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application Suitable for The FHB II-A S is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation With the FHB II-A S, the drill bit diameter is the same as the thread diameter, similar to with an anchor bolt The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art. -No. 62420 Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 Application Suitable for: Guard rails Façades Staircases Steel brackets Masts Rash protection Steelwork constructions Timber constructions Ideal for: Push-through installation ds: dsc: kts: highbond anchor FHB II-A S M10 x 60/100 stainless steel A4 kpn: 97634 kpn_dash: kpn_clear: 97634 bkpn: FISCHER 97634 bkpn_clear: FISCHER 97634 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor rod | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor rod sr_no_br_cl_ns: 97634 sr_ns: FISCHER97634
r: 08096880 p: 13.553 pid: 176258 b: FISCHER q: 0 st: lt: 8 ean: 4048962462531 sr: FISCHER 564628 sr_no_br: 564628 sr_no_br_cl: 564628 sr_cl: FISCHER564628 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 50 mm Overall length 173 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread designation M16 n: FISCHER 564628 piercing anchor FAZ II Plus 16/50 R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Stainless steel: maximum safety for outdoor use Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: piercing anchor FAZ II Plus 16/50 R stainless steel kpn: 564628 kpn_dash: kpn_clear: 564628 bkpn: FISCHER 564628 bkpn_clear: FISCHER 564628 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564628 sr_ns: FISCHER564628
